查看SKU:RB-02S102 Gesture Sensor的源代碼

[[文件:02S102001.png|500px|縮略圖|右]]
==產品概述==
Gesture Sensor模塊是基于APDS-9960傳感器的一款能夠識別手勢移動方向（上下左右）的傳感器模塊。APDS-9960芯片集成了RGB、環境光、接近和手勢檢測功能。模塊使用I2C接口，使用相應arduino庫函數即可對編程控制，傳感器返回的信號可用于作為機器人接收的控制信號，從而實現對機器人的控制。內置的識別算法相當智能，能夠把雙手從生硬的按鍵中解放出來。
==產品參數==
# 輸入電壓：3.3V - 5V
# 引腳接口：IIC接口* 1、中斷引腳 * 1
# 接口類型：直插、KF2510
# 輸出信號：數字
# 產品尺寸：30 mm * 25 mm
# 定位孔：4 * M3，間距 23mm x 18mm
# 檢測距離：10 cm
# 重量大?。?g

==使用方法==
===庫文件下載===
* 庫文件下載地址：[ALSROBOT http://pan.baidu.com/s/1o8GZz6M]
* 庫文件安裝詳細方法：[http://www.makerspace.cn/forum.php?mod=viewthread&tid=6647&fromuid=10780 Arduino 庫文件加載方法]
===例子程序===
1、測試環境<br/>
* 硬件環境：Starduino UNO R3 、傳感器V5.0擴展板、紅外手勢傳感器、8*8點陣
* 軟件環境：Arduino IDE 1.7.7

2、引腳定義<br/>
* -：電源地
* +：電源正極
* SDA：數據引腳
* SCL：時引腳

3、硬件連接
[[文件:02S10201.png|700px|縮略圖|居中]]

4、例子程序<br/>
<pre style='color:blue'>
#include <Wire.h>
#include <ALSROBOT_APDS9960.h>
const int DINPin = 4;         //數據引腳 連接到數字P4口
const int CLKPin = 5;         //時鐘引腳 連接到數字P5口
const int LTHPin = 6;         //鎖存引腳 連接到數字P6口

byte LieScan[16] = {                         //列掃描，點陣只點亮一列
  0xFE,0xFD,0xFB,0xF7,0xEF,0xDF,0xBF,0x7F
};
byte HanZi_1[] = {
  0x1c,0x7c,0x7e,0x3f,0x3f,0x7e,0x7c,0x1c    //顯示心形圖案
};
char Left[]={0x00,0x18,0x3c,0x7e,0x18,0x18,0x18,0x00};
char Down[]={0x00,0x10,0x30,0x7e,0x7e,0x30,0x10,0x00};
char Up[]={0x00,0x08,0x0c,0x7e,0x7e,0x0c,0x08,0x00};
char Right[]={0x00,0x18,0x18,0x18,0x7e,0x3c,0x18,0x00};
char Far[]={0xff,0xff,0xc3,0xc3,0xc3,0xc3,0xff,0xff};
char Near[]={0x00,0x00,0x3c,0x3c,0x3c,0x3c,0x00,0x00};
char Moren[]={0x18,0x3c,0x5a,0xff,0xff,0x5a,0x3c,0x18};

ALSROBOT_APDS9960 apds = ALSROBOT_APDS9960();
int isr_flag = 0;
int temp=0;

void setup() {
  pinMode(DINPin,OUTPUT);      //設置數據引腳為輸出
  pinMode(CLKPin,OUTPUT);      //設置鎖存引腳為輸出
  pinMode(LTHPin,OUTPUT);      //設置時鐘引腳為輸出
  // Initialize Serial port
  Serial.begin(9600);
  Serial.println();
  Serial.println(F("--------------------------------"));
  Serial.println(F("ALSROBOT APDS-9960 - GestureTest"));
  Serial.println(F("--------------------------------"));

  if ( apds.init() ) {
    Serial.println(F("APDS-9960 initialization complete"));
  } else {
    Serial.println(F("Something went wrong during APDS-9960 init!"));
  }
  
  // Start running the APDS-9960 gesture sensor engine
  if ( apds.enableGestureSensor(true) ) {
    Serial.println(F("Gesture sensor is now running"));
  } else {
    Serial.println(F("Something went wrong during gesture sensor init!"));
  }
}

void left(){
  for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Left[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }    
}

void down()
{
    for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Down[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }    
}
void up()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Up[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}

void right()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Right[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}

void far()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Far[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}

void near()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Near[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}
void moren()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, 0x00);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}



void loop() {
  
  switch(temp)
  {
      case 1:up();break;
      case 2:down();break;
      case 3:left();break;
      case 4:right();break;
      case 5:near();break;
      case 6:far();break;
      default :moren();break;
  }
  handleGesture();
}

void handleGesture() {
    if ( apds.isGestureAvailable() ) {
    switch ( apds.readGesture() ) {
      case DIR_UP:
        temp=1;
        Serial.println("UP");
        break;
      case DIR_DOWN:
      temp=2;
        Serial.println("DOWN");
        break;
      case DIR_LEFT:
        temp=3;
        Serial.println("LEFT");
        break;
      case DIR_RIGHT:
        temp=4;
        Serial.println("RIGHT");
        break;
      case DIR_NEAR:
        temp=5;
        Serial.println("NEAR");
        break;
      case DIR_FAR:
        temp=6;
        Serial.println("FAR");
        break;
      default:temp=7;
        Serial.println("NONE");
    }
  }
}
</pre>
5、程序效果
如圖所示，當手滑動時，點陣顯示相應的滑動方向
[[文件:02S10202.png|700px|縮略圖|居中]]

==產品相關推薦==
[[文件:erweima.png|230px|無框|右]]
===產品購買地址===
* [http://www.gharee.com/goods-771.html 手勢識別傳感器]
===相關學習資料===
* [http://pan.baidu.com/s/1i45wtvR apds9960_datasheet 下載]
* [http://www.makerspace.cn/forum.php?mod=viewthread&tid=6786&page=1&extra=#pid21424 RB - 02S102 Gesture Sensor 手勢識別模塊庫文件下載]