“(SKU:RB-03T006)NRF24L01無線數傳模塊”的版本間的差異

2016年4月11日 (一) 17:29的最后版本

產品概述

NRF24L01是一款新型單片射頻收發器件，工作于2.4 GHz～2.5 GHz ISM頻段。內置頻率合成器、功率放大器、晶體振蕩器、調制器等功能模塊，并融合了增強型ShockBurst技術，其中輸出功率和通信頻道可通過程序進 行配置。NRF24L01功耗低，在以-6 dBm的功率發射時，工作電流也只有9 mA；接收時，工作電流只有12.3 mA，多種低功率工作模式(掉電模式和空閑模式)使節能設計更方便。

規格參數

1. 2Mbit/s速率下接收時的峰值電流12.5mA
2. 在2Mbit/s速率下@0dBm輸出時的峰值電流11mA
3. 掉電模式下的功耗400nA
4. 待機模式下的功耗32uA
5. 130us 的快速切換和喚醒時間
6. 具有片內穩壓器oltage regulators
7. 可在1.9 to 3.6V低電壓工作
8. MultiCeiverMT硬件提供同時6個接收機的功能，2Mbit/s 使得高質量的VoIP成為可能

使用方法

引腳說明

引腳說明：

• CE：使能發射或接收；
• CSN、 SCK、 MOSI、 MISO： SPI引腳，通過此引腳配置nRF24L01
• IRQ：中斷

應用例程

1.庫文件下載
NRF2401庫文件及使用例程下載地址
2.連接Arduino和NRF2401模塊
連接注意事項：

• VCC引腳的電壓范圍2.3 - 3.6之間，超過 3.6V 模塊會燒掉， 建議使用3.3V左右。
• 該模塊也可以通過普通 IO 口模擬 SPI 時序進行讀寫數據操作。
• 使用 2 個模塊同時發射時，兩者頻道間隔應該至少相差1MHZ,否則同頻道之間易干擾。

3.代碼下載
發送端代碼

/*********************************************************************
**  Device:  nRF24L01+   TX                                           **

**   SPI***********                                                 **
**   CE -   to digital pin 8                                        **
**   CSN -  to digital pin 9  (SS pin)                              **
**   CLK -  to digital pin 10 (SCK pin)                             **
**   MOSI - to digital pin 11 (MOSI pin)                            **
**   MISO - to digital pin 12 (MISO pin)                            **
**   IRQ -  to digital pin 13                                       **
*********************************************************************/

#include "NRF24L01.h"

//***************************************************
#define TX_ADR_WIDTH    5   // 5 unsigned chars TX address width
#define RX_ADR_WIDTH    5   // 5 unsigned chars RX address width
#define TX_PLOAD_WIDTH  32  // 32 unsigned chars TX payload
#define RX_PLOAD_WIDTH  32  // 32 unsigned chars RX payload

unsigned char TX_ADDRESS[TX_ADR_WIDTH]  = 
{
  0x34,0x43,0x10,0x10,0x01
}; // Define a static TX address
unsigned char RX_ADDRESS[RX_ADR_WIDTH]  = 
{
  0x34,0x43,0x10,0x10,0x01
}; // Define a static RX address

unsigned char TX_BUF[TX_PLOAD_WIDTH]={0};

//***************************************************
void setup() 
{
  SPI_DIR = ( NRFCE + NRFSCK + NRFCSN + NRFMOSI);
  SPI_DIR &=~ ( NRFIRQ + NRFMISO);

  delay(100);
  init_io();
  init_NRF24L01();
  
  Serial.begin(9600);
  
  TX_BUF[1] = 0x01 ;	
  TX_BUF[2] = 0x02 ;	
  nRF24L01_TxPacket(TX_BUF);
  delay(50);
}

void loop() 
{
   unsigned char status=0;
  
  //  status=SPI_Read(STATUS);
 //   if(status&TX_DS)
    for(; ;)
    {     
      TX_BUF[1] = 0x01 ;	
      TX_BUF[2] = 0x02 ;      
      Serial.println("****************START TX**********************");
      Serial.print("TX_BUF[1]=0x");
      Serial.println(TX_BUF[1],HEX);
      Serial.print("TX_BUF[2]=0x");
      Serial.println(TX_BUF[2],HEX);  
      
     delay(1000);	  
     nRF24L01_TxPacket(TX_BUF);	// Transmit Tx buffer data
     SPI_RW_Reg(WRITE_REG+STATUS,0XFF); 
     
     TX_BUF[1] = 0x00;
     TX_BUF[2] = 0x00;
   }
}

//**************************************************
// Function: init_io();
// Description:
// flash led one time,chip enable(ready to TX or RX Mode),
// Spi disable,Spi clock line init high
//**************************************************
void init_io(void)
{
  SPI_PORT&=~NRFCE;			// chip enable
  SPI_PORT|=NRFCSN;			// Spi disable	
  SPI_PORT&=~NRFSCK;			// Spi clock line init high
}

/**************************************************
 * Function: SPI_RW();
 * 
 * Description:
 * Writes one unsigned char to nRF24L01, and return the unsigned char read
 * from nRF24L01 during write, according to SPI protocol
 **************************************************/
unsigned char SPI_RW(unsigned char Byte)
{
  unsigned char i;
  for(i=0;i<8;i++)                      // output 8-bit
  {
    if(Byte&0x80)
    {
      SPI_PORT |=NRFMOSI;    // output 'unsigned char', MSB to MOSI
    }
    else
    {
      SPI_PORT &=~NRFMOSI;
    }
    SPI_PORT|=NRFSCK;                      // Set SCK high..
    Byte <<= 1;                         // shift next bit into MSB..
    if(SPI_IN & NRFMISO)
    {
      Byte |= 1;       	        // capture current MISO bit
    }
    SPI_PORT&=~NRFSCK;            	        // ..then set SCK low again
  }
  return(Byte);           	        // return read unsigned char
}
/**************************************************/

/**************************************************
 * Function: SPI_RW_Reg();
 * 
 * Description:
 * Writes value 'value' to register 'reg'
/**************************************************/
unsigned char SPI_RW_Reg(unsigned char reg, unsigned char value)
{
  unsigned char status;

  SPI_PORT&=~NRFCSN;                   // CSN low, init SPI transaction
  status = SPI_RW(reg);             // select register
  SPI_RW(value);                    // ..and write value to it..
  SPI_PORT|=NRFCSN;                    // CSN high again

  return(status);                   // return nRF24L01 status unsigned char
}
/**************************************************/

/**************************************************
 * Function: SPI_Read();
 * 
 * Description:
 * Read one unsigned char from nRF24L01 register, 'reg'
/**************************************************/
unsigned char SPI_Read(unsigned char reg)
{
  unsigned char reg_val;

  SPI_PORT&=~NRFCSN;                // CSN low, initialize SPI communication...
  SPI_RW(reg);                   // Select register to read from..
  reg_val = SPI_RW(0);           // ..then read register value
  SPI_PORT|=NRFCSN;                 // CSN high, terminate SPI communication

  return(reg_val);               // return register value
}
/**************************************************/

/**************************************************
 * Function: SPI_Read_Buf();
 * 
 * Description:
 * Reads 'unsigned chars' #of unsigned chars from register 'reg'
 * Typically used to read RX payload, Rx/Tx address
/**************************************************/
unsigned char SPI_Read_Buf(unsigned char reg, unsigned char *pBuf, unsigned char bytes)
{
  unsigned char status,i;

  SPI_PORT&=~NRFCSN;                   // Set CSN low, init SPI tranaction
  status = SPI_RW(reg);       	    // Select register to write to and read status unsigned char

  for(i=0;i<bytes;i++)
  {
    pBuf[i] = SPI_RW(0);    // Perform SPI_RW to read unsigned char from nRF24L01
  }

  SPI_PORT|=NRFCSN;                   // Set CSN high again

  return(status);                  // return nRF24L01 status unsigned char
}
/**************************************************/

/**************************************************
 * Function: SPI_Write_Buf();
 * 
 * Description:
 * Writes contents of buffer '*pBuf' to nRF24L01
 * Typically used to write TX payload, Rx/Tx address
/**************************************************/
unsigned char SPI_Write_Buf(unsigned char reg, unsigned char *pBuf, unsigned char bytes)
{
  unsigned char status,i;

  SPI_PORT&=~NRFCSN;                   // Set CSN low, init SPI tranaction
  status = SPI_RW(reg);             // Select register to write to and read status unsigned char
  for(i=0;i<bytes; i++)             // then write all unsigned char in buffer(*pBuf)
  {
    SPI_RW(*pBuf++);
  }
  SPI_PORT|=NRFCSN;                   // Set CSN high again
  return(status);                  // return nRF24L01 status unsigned char
}

/**************************************************/

/*************************************************** 
 * Function: nRF24L01_TxPacket(unsigned char * tx_buf)
 * Description:
 * sent tx_buf data
/**************************************************/
void nRF24L01_TxPacket(unsigned char * tx_buf)
{
	SPI_PORT&=~NRFCE;			//StandBy I mode
	SPI_Write_Buf(WRITE_REG + RX_ADDR_P0, TX_ADDRESS, TX_ADR_WIDTH); 
	SPI_Write_Buf(WR_TX_PLOAD, tx_buf, TX_PLOAD_WIDTH); 			
	SPI_RW_Reg(WRITE_REG + CONFIG, 0x0e);   		
       SPI_PORT|=NRFCE;
       delay(10);
}


/**************************************************
 * Function: init_NRF24L01();
 * 
 * Description:
 * This function initializes one nRF24L01 device to
 * TX mode, set TX address, set RX address for auto.ack,
 * fill TX payload, select RF channel, datarate & TX pwr.
 * PWR_UP is set, CRC(2 unsigned chars) is enabled, & PRIM:TX.
 * 
 * ToDo: One high pulse(>10us) on CE will now send this
 * packet and expext an acknowledgment from the RX device.
 **************************************************/
void init_NRF24L01(void)
{
  SPI_PORT&=~NRFCE;

  SPI_Write_Buf(WRITE_REG + TX_ADDR, TX_ADDRESS, TX_ADR_WIDTH);    // Writes TX_Address to nRF24L01
  SPI_Write_Buf(WRITE_REG + RX_ADDR_P0, RX_ADDRESS, RX_ADR_WIDTH); // RX_Addr0 same as TX_Adr for Auto.Ack
  
  SPI_RW_Reg(WRITE_REG + EN_AA, 0x01);     // Enable Auto.Ack:Pipe0
  SPI_RW_Reg(WRITE_REG + EN_RXADDR, 0x01);  // Enable Pipe0  If need more channel ,pls refer to age21  
  SPI_RW_Reg(WRITE_REG + RF_CH, 0);        //  setup channel is 2.4GHZ 
  SPI_RW_Reg(WRITE_REG + RX_PW_P0, RX_PLOAD_WIDTH); //Setup reivce data length 20byte
  SPI_RW_Reg(WRITE_REG + RF_SETUP, 0x07);   		// TX_PWR:0dBm, Datarate:2Mbps, LNA:HCURR

  SPI_PORT|=NRFCE;
}

接收端代碼：

/*********************************************************************
**  Device:  nRF24L01+   RX                                           **

**   SPI***********                                                 **
**   CE -   to digital pin 8                                        **
**   CSN -  to digital pin 9  (SS pin)                              **
**   CLK -  to digital pin 10 (SCK pin)                              **
**   MOSI - to digital pin 11 (MOSI pin)                            **
**   MISO - to digital pin 12 (MISO pin)                            **
**   IRQ -  to digital pin 13                                          **
*********************************************************************/

#include "NRF24L01.h"

//***************************************************
#define TX_ADR_WIDTH    5   // 5 unsigned chars TX address width
#define RX_ADR_WIDTH    5   // 5 unsigned chars RX address width
#define TX_PLOAD_WIDTH  32  // 32 unsigned chars TX payload
#define RX_PLOAD_WIDTH  32  // 32 unsigned chars RX payload

unsigned char status=0;
unsigned char TX_ADDRESS[TX_ADR_WIDTH]  = 
{
  0x34,0x43,0x10,0x10,0x01
}; // Define a static TX address

unsigned char RX_ADDRESS[RX_ADR_WIDTH]  = 
{
  0x34,0x43,0x10,0x10,0x01
}; // Define a static RX address

unsigned char RX_BUF[TX_PLOAD_WIDTH]={0};
unsigned char TX_BUF[TX_PLOAD_WIDTH]={0};

//***************************************************
void setup() 
{
  SPI_DIR = ( NRFCE + NRFSCK + NRFCSN + NRFMOSI);
  SPI_DIR &=~ ( NRFIRQ + NRFMISO);

  delay(100);
  init_io();
  init_NRF24L01();
  
  Serial.begin(9600);  
}

void loop() 
{ 
	nRF24L01_RxPacket(RX_BUF);					
	if((RX_BUF[1]==0x01)&&(RX_BUF[2]==0x02))
	{	 					  
                     Serial.println("****************RX SUCCEED**********************");	                   
                     Serial.print("RX_BUF[1]=0x");
                     Serial.println(RX_BUF[1],HEX);
                     Serial.print("RX_BUF[2]=0x");
                     Serial.println(RX_BUF[2],HEX);                     
	}
	RX_BUF[1] = 0x00;
	RX_BUF[2] = 0x00; 
}


//**************************************************
// Function: init_io();
// Description:
// flash led one time,chip enable(ready to TX or RX Mode),
// Spi disable,Spi clock line init high
//**************************************************
void init_io(void)
{
  SPI_PORT&=~NRFCE;			// chip enable
  SPI_PORT|=NRFCSN;			// Spi disable	
  SPI_PORT&=~NRFSCK;			// Spi clock line init high
}

/**************************************************
 * Function: SPI_RW();
 * 
 * Description:
 * Writes one unsigned char to nRF24L01, and return the unsigned char read
 * from nRF24L01 during write, according to SPI protocol
 **************************************************/
unsigned char SPI_RW(unsigned char Byte)
{
  unsigned char i;
  for(i=0;i<8;i++)                      // output 8-bit
  {
    if(Byte&0x80)
    {
      SPI_PORT |=NRFMOSI;    // output 'unsigned char', MSB to MOSI
    }
    else
    {
      SPI_PORT &=~NRFMOSI;
    }
    SPI_PORT|=NRFSCK;                      // Set SCK high..
    Byte <<= 1;                         // shift next bit into MSB..
    if(SPI_IN & NRFMISO)
    {
      Byte |= 1;       	        // capture current MISO bit
    }
    SPI_PORT&=~NRFSCK;            	        // ..then set SCK low again
  }
  return(Byte);           	        // return read unsigned char
}
/**************************************************/

/**************************************************
 * Function: SPI_RW_Reg();
 * 
 * Description:
 * Writes value 'value' to register 'reg'
/**************************************************/
unsigned char SPI_RW_Reg(unsigned char reg, unsigned char value)
{
  unsigned char status;

  SPI_PORT&=~NRFCSN;                   // CSN low, init SPI transaction
  status = SPI_RW(reg);             // select register
  SPI_RW(value);                    // ..and write value to it..
  SPI_PORT|=NRFCSN;                    // CSN high again

  return(status);                   // return nRF24L01 status unsigned char
}
/**************************************************/

/**************************************************
 * Function: SPI_Read();
 * 
 * Description:
 * Read one unsigned char from nRF24L01 register, 'reg'
/**************************************************/
unsigned char SPI_Read(unsigned char reg)
{
  unsigned char reg_val;

  SPI_PORT&=~NRFCSN;                // CSN low, initialize SPI communication...
  SPI_RW(reg);                   // Select register to read from..
  reg_val = SPI_RW(0);           // ..then read register value
  SPI_PORT|=NRFCSN;                 // CSN high, terminate SPI communication

  return(reg_val);               // return register value
}
/**************************************************/

/**************************************************
 * Function: SPI_Read_Buf();
 * 
 * Description:
 * Reads 'unsigned chars' #of unsigned chars from register 'reg'
 * Typically used to read RX payload, Rx/Tx address
/**************************************************/
unsigned char SPI_Read_Buf(unsigned char reg, unsigned char *pBuf, unsigned char bytes)
{
  unsigned char status,i;

  SPI_PORT&=~NRFCSN;                   // Set CSN low, init SPI tranaction
  status = SPI_RW(reg);       	    // Select register to write to and read status unsigned char

  for(i=0;i<bytes;i++)
  {
    pBuf[i] = SPI_RW(0);    // Perform SPI_RW to read unsigned char from nRF24L01
  }

  SPI_PORT|=NRFCSN;                   // Set CSN high again

  return(status);                  // return nRF24L01 status unsigned char
}
/**************************************************/

/**************************************************
 * Function: SPI_Write_Buf();
 * 
 * Description:
 * Writes contents of buffer '*pBuf' to nRF24L01
 * Typically used to write TX payload, Rx/Tx address
/**************************************************/
unsigned char SPI_Write_Buf(unsigned char reg, unsigned char *pBuf, unsigned char bytes)
{
  unsigned char status,i;

  SPI_PORT&=~NRFCSN;                   // Set CSN low, init SPI tranaction
  status = SPI_RW(reg);             // Select register to write to and read status unsigned char
  for(i=0;i<bytes; i++)             // then write all unsigned char in buffer(*pBuf)
  {
    SPI_RW(*pBuf++);
  }
  SPI_PORT|=NRFCSN;                   // Set CSN high again
  return(status);                  // return nRF24L01 status unsigned char
}


/*************************************************** 
 * Function: nRF24L01_RxPacket(unsigned char* rx_buf) 
 * Description:
 * Receive data put into rx_buf 
/**************************************************/
unsigned char nRF24L01_RxPacket(unsigned char* rx_buf)
{
    unsigned char status;
    unsigned char ret=0;

    SPI_PORT&=~NRFCE;    // chip enable	
    SPI_RW_Reg(WRITE_REG + CONFIG, 0x0f);   		// IRQ收發完成中斷響應，16位CRC	，主接收
    SPI_PORT|=NRFCE;	
   delay(10);
   
    status=SPI_Read(STATUS);	//read status to judge if receive data 
    if(status&RX_DR)				
	{
	    SPI_PORT&=~NRFCE; 
	     SPI_Read_Buf(RD_RX_PLOAD,rx_buf,TX_PLOAD_WIDTH);// read receive payload from RX_FIFO buffer
	     ret =1;			//finish read data signal
	}
	SPI_RW_Reg(WRITE_REG+STATUS,status);   //after receive data ,RX_DR,TX_DS,MAX_PT  all set 1 to clear interupt signal

    return ret;
}

/**************************************************
 * Function: init_NRF24L01();
 * 
 * Description:
 * This function initializes one nRF24L01 device to
 * TX mode, set TX address, set RX address for auto.ack,
 * fill TX payload, select RF channel, datarate & TX pwr.
 * PWR_UP is set, CRC(2 unsigned chars) is enabled, & PRIM:TX.
 * 
 * ToDo: One high pulse(>10us) on CE will now send this
 * packet and expext an acknowledgment from the RX device.
 **************************************************/
void init_NRF24L01(void)
{
  SPI_PORT&=~NRFCE;

  SPI_Write_Buf(WRITE_REG + TX_ADDR, TX_ADDRESS, TX_ADR_WIDTH);    // Writes TX_Address to nRF24L01
  SPI_Write_Buf(WRITE_REG + RX_ADDR_P0, RX_ADDRESS, RX_ADR_WIDTH); // RX_Addr0 same as TX_Adr for Auto.Ack
  
  SPI_RW_Reg(WRITE_REG + EN_AA, 0x01);     // Enable Auto.Ack:Pipe0
  SPI_RW_Reg(WRITE_REG + EN_RXADDR, 0x01);  // Enable Pipe0  If need more channel ,pls refer to age21  
  SPI_RW_Reg(WRITE_REG + RF_CH, 0);        //  setup channel is 2.4GHZ 
  SPI_RW_Reg(WRITE_REG + RX_PW_P0, RX_PLOAD_WIDTH); //Setup reivce data length 20byte
  SPI_RW_Reg(WRITE_REG + RF_SETUP, 0x07);   		// TX_PWR:0dBm, Datarate:2Mbps, LNA:HCURR

  SPI_PORT|=NRFCE;
}

產品相關推薦

購買地址

NRF24L01無線數傳模塊

周邊產品推薦

無線數傳模塊
無線射頻模塊

相關問題解答

相關學習資料

奧松機器人技術論壇