“SKU:RB-02S102 Gesture Sensor”的版本間的差異

來自ALSROBOT WiKi
跳轉至： 導航、 搜索
（→?產品相關推薦）
 
（未顯示1個用戶的11個中間版本）
第11行： 第11行：
 
# 檢測距離：10 cm
 
# 檢測距離：10 cm
 
# 重量大?。?g
 
# 重量大?。?g
 +
* 產品尺寸圖：
 +
[[文件:size041.jpg|500px|縮略圖|居中]]
  
?
==使用方法==
+
==使用方法_1（Arduino 控制器）==
?
===庫文件下載===
+
===使用硬件===
?
* 庫文件下載地址：[ALSROBOT http://pan.baidu.com/s/1o8GZz6M]
+
* 1 * Arduino UNO 控制器
?
* 庫文件安裝詳細方法：[http://www.makerspace.cn/forum.php?mod=viewthread&tid=6647&fromuid=10780 Arduino 庫文件加載方法]
+
* 杜邦線若干
?
===例子程序===
+
* USB 數據線
 +
===硬件連接===
 +
[[文件:02S10211.png|700px|縮略圖|居中]]
 +
===Arduino_code_1===
 +
<pre style='color:blue'>#include <Wire.h>
 +
#include <ALS_APDS9960.h>
 +
 
 +
ALS_APDS9960 apds = ALS_APDS9960();
 +
int isr_flag = 0;
 +
 
 +
void setup() {
 +
  Serial.begin(9600);
 +
  Serial.println();
 +
  Serial.println(F("--------------------------------"));
 +
  Serial.println(F("SparkFun APDS-9960 - GestureTest"));
 +
  Serial.println(F("--------------------------------"));
 +
 
 +
  if ( apds.init() ) {
 +
    Serial.println(F("APDS-9960 initialization complete"));
 +
  } else {
 +
    Serial.println(F("Something went wrong during APDS-9960 init!"));
 +
  }
 +
 
 +
  // Start running the APDS-9960 gesture sensor engine
 +
  if ( apds.enableGestureSensor(true) ) {
 +
    Serial.println(F("Gesture sensor is now running"));
 +
  } else {
 +
    Serial.println(F("Something went wrong during gesture sensor init!"));
 +
  }
 +
}
 +
 
 +
void loop() {
 +
    handleGesture();
 +
    delay(50);
 +
}
 +
 
 +
void handleGesture() {
 +
    if ( apds.isGestureAvailable() ) {
 +
    switch ( apds.readGesture() ) {
 +
      case DIR_UP:
 +
        Serial.println("UP");
 +
        break;
 +
      case DIR_DOWN:
 +
        Serial.println("DOWN");
 +
        break;
 +
      case DIR_LEFT:
 +
        Serial.println("LEFT");
 +
        break;
 +
      case DIR_RIGHT:
 +
        Serial.println("RIGHT");
 +
        break;
 +
      case DIR_NEAR:
 +
        Serial.println("NEAR");
 +
        break;
 +
      case DIR_FAR:
 +
        Serial.println("FAR");
 +
        break;
 +
      default:
 +
        Serial.println("NONE");
 +
    }
 +
  }
 +
}</pre>
 +
===程序效果===
 +
手在上下左右遠近滑過經過傳感器時，串口會打印如圖所示的數據
 +
[[文件:02S10210.png|700px|縮略圖|居中]]
 +
 
 +
==使用方法_2（Arduino 控制器）==
 +
===使用硬件===
 +
* 1 * LED 發光模塊
 +
* 1 * Arduino 控制器
 +
* 1 * 傳感器擴展板 V5.0
 +
* 1 * 手勢傳感器
 +
* 1 * USB 數據線
 +
* 1 * 4P 傳感器連接線
 +
* 杜邦線若干
 +
 
 +
===硬件連接===
 +
[[文件:02S10220.png|700px|縮略圖|居中]]
 +
 
 +
===Arduino_code_2===
 +
<pre style='color:blue'>#include <Wire.h>
 +
#include <ALS_APDS9960.h>
 +
#define led 4
 +
#define APDS9960_INT    2
 +
ALS_APDS9960 apds = ALS_APDS9960();
 +
int temp = 0;
 +
int isr_flag = 0;
 +
 
 +
void setup() {
 +
  pinMode(led,OUTPUT);
 +
  pinMode(APDS9960_INT, INPUT);
 +
 
 +
  Serial.begin(9600);
 +
  Serial.println();
 +
  Serial.println(F("--------------------------------"));
 +
  Serial.println(F("ALS_APDS-9960 - GestureTest"));
 +
  Serial.println(F("--------------------------------"));
 +
 
 +
  attachInterrupt(0, interruptRoutine, FALLING);
 +
 
 +
  if ( apds.init() ) {
 +
    Serial.println(F("APDS-9960 initialization complete"));
 +
  } else {
 +
    Serial.println(F("Something went wrong during APDS-9960 init!"));
 +
  }
 +
 
 +
  if ( apds.enableGestureSensor(true) ) {
 +
    Serial.println(F("Gesture sensor is now running"));
 +
  } else {
 +
    Serial.println(F("Something went wrong during gesture sensor init!"));
 +
  }
 +
}
 +
 
 +
void loop() {
 +
  if( isr_flag == 1 ) {
 +
    detachInterrupt(0);
 +
    handleGesture();
 +
    isr_flag = 0;
 +
    attachInterrupt(0, interruptRoutine, FALLING);
 +
  }
 +
 
 +
}
 +
 
 +
void interruptRoutine() {
 +
  isr_flag = 1;
 +
      switch(temp){
 +
      case 1:
 +
        digitalWrite(led,HIGH);
 +
        break;
 +
      case 2:
 +
        digitalWrite(led,LOW);
 +
        break;
 +
      }
 +
}
 +
 
 +
void handleGesture() {
 +
    if ( apds.isGestureAvailable() ) {
 +
    switch ( apds.readGesture() ) {
 +
      case DIR_UP:
 +
        Serial.println("UP");
 +
        temp = 1;
 +
        break;
 +
      case DIR_DOWN:
 +
        Serial.println("DOWN");
 +
        temp = 2;
 +
        break;
 +
      case DIR_LEFT:
 +
        Serial.println("LEFT");
 +
        break;
 +
      case DIR_RIGHT:
 +
        Serial.println("RIGHT");
 +
        break;
 +
      case DIR_NEAR:
 +
        Serial.println("NEAR");
 +
        break;
 +
      case DIR_FAR:
 +
        Serial.println("FAR");
 +
        break;
 +
      default:
 +
        Serial.println("NONE");
 +
        temp = 0;
 +
    }
 +
  }
 +
}</pre>
 +
===程序效果===
 +
* 向上滑動時，通過串口打印‘UP’，同時 LED 亮起
 +
* 向下滑動時，通過串口打印‘DOWM’,同時 LED 熄滅
 +
 
 +
==應用案例==
 
1、測試環境<br/>
 
1、測試環境<br/>
 
* 硬件環境：Starduino UNO R3 、傳感器V5.0擴展板、紅外手勢傳感器、8*8點陣
 
* 硬件環境：Starduino UNO R3 、傳感器V5.0擴展板、紅外手勢傳感器、8*8點陣
第218行： 第388行：
 
==產品相關推薦==
 
==產品相關推薦==
 
[[文件:erweima.png|230px|無框|右]]
 
[[文件:erweima.png|230px|無框|右]]
 +
===資料下載===
 +
* [http://www.makerspace.cn/forum.php?mod=viewthread&tid=6647&fromuid=10780 Arduino 庫文件加載方法]
 +
* 例程及芯片手冊下載鏈接： https://pan.baidu.com/s/1UWH-DQiHI-AbRQPh_9PI6Q 提取碼：qip3
 
===產品購買地址===
 
===產品購買地址===
 
* [http://www.gharee.com/goods-771.html 手勢識別傳感器]
 
* [http://www.gharee.com/goods-771.html 手勢識別傳感器]
?
===相關學習資料===
 
?
* [http://pan.baidu.com/s/1i45wtvR apds9960_datasheet 下載]
 
?
* [http://www.makerspace.cn/forum.php?mod=viewthread&tid=6786&page=1&extra=#pid21424 RB - 02S102 Gesture Sensor 手勢識別模塊庫文件下載]
 

2021年7月27日 (二) 17:37的最后版本

02S102001.png

目錄

產品概述

Gesture Sensor模塊是基于APDS-9960傳感器的一款能夠識別手勢移動方向（上下左右）的傳感器模塊。APDS-9960芯片集成了RGB、環境光、接近和手勢檢測功能。模塊使用I2C接口，使用相應arduino庫函數即可對編程控制，傳感器返回的信號可用于作為機器人接收的控制信號，從而實現對機器人的控制。內置的識別算法相當智能，能夠把雙手從生硬的按鍵中解放出來。

產品參數

  1. 輸入電壓：3.3V - 5V
  2. 引腳接口：IIC接口* 1、中斷引腳 * 1
  3. 接口類型：直插、KF2510
  4. 輸出信號：數字
  5. 產品尺寸：30 mm * 25 mm
  6. 定位孔：4 * M3，間距 23mm x 18mm
  7. 檢測距離：10 cm
  8. 重量大?。?g
  • 產品尺寸圖：
Size041.jpg

使用方法_1（Arduino 控制器）

使用硬件

  • 1 * Arduino UNO 控制器
  • 杜邦線若干
  • USB 數據線

硬件連接

02S10211.png

Arduino_code_1

#include <Wire.h>
#include <ALS_APDS9960.h>

ALS_APDS9960 apds = ALS_APDS9960();
int isr_flag = 0;

void setup() {
  Serial.begin(9600);
  Serial.println();
  Serial.println(F("--------------------------------"));
  Serial.println(F("SparkFun APDS-9960 - GestureTest"));
  Serial.println(F("--------------------------------"));

  if ( apds.init() ) {
    Serial.println(F("APDS-9960 initialization complete"));
  } else {
    Serial.println(F("Something went wrong during APDS-9960 init!"));
  }
  
  // Start running the APDS-9960 gesture sensor engine
  if ( apds.enableGestureSensor(true) ) {
    Serial.println(F("Gesture sensor is now running"));
  } else {
    Serial.println(F("Something went wrong during gesture sensor init!"));
  }
}

void loop() {
    handleGesture();
    delay(50);
}

void handleGesture() {
    if ( apds.isGestureAvailable() ) {
    switch ( apds.readGesture() ) {
      case DIR_UP:
        Serial.println("UP");
        break;
      case DIR_DOWN:
        Serial.println("DOWN");
        break;
      case DIR_LEFT:
        Serial.println("LEFT");
        break;
      case DIR_RIGHT:
        Serial.println("RIGHT");
        break;
      case DIR_NEAR:
        Serial.println("NEAR");
        break;
      case DIR_FAR:
        Serial.println("FAR");
        break;
      default:
        Serial.println("NONE");
    }
  }
}

程序效果

手在上下左右遠近滑過經過傳感器時，串口會打印如圖所示的數據

02S10210.png

使用方法_2（Arduino 控制器）

使用硬件

  • 1 * LED 發光模塊
  • 1 * Arduino 控制器
  • 1 * 傳感器擴展板 V5.0
  • 1 * 手勢傳感器
  • 1 * USB 數據線
  • 1 * 4P 傳感器連接線
  • 杜邦線若干

硬件連接

02S10220.png

Arduino_code_2

#include <Wire.h>
#include <ALS_APDS9960.h>
#define led 4
#define APDS9960_INT    2 
ALS_APDS9960 apds = ALS_APDS9960();
int temp = 0;
int isr_flag = 0;

void setup() {
  pinMode(led,OUTPUT);
  pinMode(APDS9960_INT, INPUT);
  
  Serial.begin(9600);
  Serial.println();
  Serial.println(F("--------------------------------"));
  Serial.println(F("ALS_APDS-9960 - GestureTest"));
  Serial.println(F("--------------------------------"));
  
  attachInterrupt(0, interruptRoutine, FALLING);
  
  if ( apds.init() ) {
    Serial.println(F("APDS-9960 initialization complete"));
  } else {
    Serial.println(F("Something went wrong during APDS-9960 init!"));
  }
  
  if ( apds.enableGestureSensor(true) ) {
    Serial.println(F("Gesture sensor is now running"));
  } else {
    Serial.println(F("Something went wrong during gesture sensor init!"));
  }
}

void loop() {
  if( isr_flag == 1 ) {
    detachInterrupt(0);
    handleGesture();
    isr_flag = 0;
    attachInterrupt(0, interruptRoutine, FALLING);
  }

}

void interruptRoutine() {
  isr_flag = 1;
      switch(temp){
      case 1:
        digitalWrite(led,HIGH);
        break;
      case 2:
        digitalWrite(led,LOW);
        break;
      }
}

void handleGesture() {
    if ( apds.isGestureAvailable() ) {
    switch ( apds.readGesture() ) {
      case DIR_UP:
        Serial.println("UP");
        temp = 1;
        break;
      case DIR_DOWN:
        Serial.println("DOWN");
        temp = 2;
        break;
      case DIR_LEFT:
        Serial.println("LEFT");
        break;
      case DIR_RIGHT:
        Serial.println("RIGHT");
        break;
      case DIR_NEAR:
        Serial.println("NEAR");
        break;
      case DIR_FAR:
        Serial.println("FAR");
        break;
      default:
        Serial.println("NONE");
        temp = 0;
    }
  }
}

程序效果

  • 向上滑動時，通過串口打印‘UP’，同時 LED 亮起
  • 向下滑動時，通過串口打印‘DOWM’,同時 LED 熄滅

應用案例

1、測試環境

  • 硬件環境：Starduino UNO R3 、傳感器V5.0擴展板、紅外手勢傳感器、8*8點陣
  • 軟件環境：Arduino IDE 1.7.7

2、引腳定義

  • -：電源地
  • +：電源正極
  • SDA：數據引腳
  • SCL：時引腳

3、硬件連接

02S10201.png

4、例子程序

#include <Wire.h>
#include <ALSROBOT_APDS9960.h>
const int DINPin = 4;         //數據引腳 連接到數字P4口
const int CLKPin = 5;         //時鐘引腳 連接到數字P5口
const int LTHPin = 6;         //鎖存引腳 連接到數字P6口

byte LieScan[16] = {                         //列掃描，點陣只點亮一列
  0xFE,0xFD,0xFB,0xF7,0xEF,0xDF,0xBF,0x7F
};
byte HanZi_1[] = {
  0x1c,0x7c,0x7e,0x3f,0x3f,0x7e,0x7c,0x1c    //顯示心形圖案
};
char Left[]={0x00,0x18,0x3c,0x7e,0x18,0x18,0x18,0x00};
char Down[]={0x00,0x10,0x30,0x7e,0x7e,0x30,0x10,0x00};
char Up[]={0x00,0x08,0x0c,0x7e,0x7e,0x0c,0x08,0x00};
char Right[]={0x00,0x18,0x18,0x18,0x7e,0x3c,0x18,0x00};
char Far[]={0xff,0xff,0xc3,0xc3,0xc3,0xc3,0xff,0xff};
char Near[]={0x00,0x00,0x3c,0x3c,0x3c,0x3c,0x00,0x00};
char Moren[]={0x18,0x3c,0x5a,0xff,0xff,0x5a,0x3c,0x18};

ALSROBOT_APDS9960 apds = ALSROBOT_APDS9960();
int isr_flag = 0;
int temp=0;

void setup() {
  pinMode(DINPin,OUTPUT);      //設置數據引腳為輸出
  pinMode(CLKPin,OUTPUT);      //設置鎖存引腳為輸出
  pinMode(LTHPin,OUTPUT);      //設置時鐘引腳為輸出
  // Initialize Serial port
  Serial.begin(9600);
  Serial.println();
  Serial.println(F("--------------------------------"));
  Serial.println(F("ALSROBOT APDS-9960 - GestureTest"));
  Serial.println(F("--------------------------------"));

  if ( apds.init() ) {
    Serial.println(F("APDS-9960 initialization complete"));
  } else {
    Serial.println(F("Something went wrong during APDS-9960 init!"));
  }
  
  // Start running the APDS-9960 gesture sensor engine
  if ( apds.enableGestureSensor(true) ) {
    Serial.println(F("Gesture sensor is now running"));
  } else {
    Serial.println(F("Something went wrong during gesture sensor init!"));
  }
}

void left(){
  for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Left[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }    
}

void down()
{
    for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Down[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }    
}
void up()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Up[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}

void right()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Right[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}

void far()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Far[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}

void near()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, Near[x]);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}
void moren()
{
       for(unsigned char times_1 = 0;times_1 <250;times_1++) {  //持續刷新250次
    for(char x = 0;x <8;x++) {
      shiftOut(DINPin, CLKPin, MSBFIRST, LieScan[x]);  //先選擇列
      shiftOut(DINPin, CLKPin, MSBFIRST, 0x00);  //再送行數據
      digitalWrite(LTHPin, LOW);    //刷新顯示
      digitalWrite(LTHPin, HIGH);
    }
  }   
}



void loop() {
  
  switch(temp)
  {
      case 1:up();break;
      case 2:down();break;
      case 3:left();break;
      case 4:right();break;
      case 5:near();break;
      case 6:far();break;
      default :moren();break;
  }
  handleGesture();
}

void handleGesture() {
    if ( apds.isGestureAvailable() ) {
    switch ( apds.readGesture() ) {
      case DIR_UP:
        temp=1;
        Serial.println("UP");
        break;
      case DIR_DOWN:
      temp=2;
        Serial.println("DOWN");
        break;
      case DIR_LEFT:
        temp=3;
        Serial.println("LEFT");
        break;
      case DIR_RIGHT:
        temp=4;
        Serial.println("RIGHT");
        break;
      case DIR_NEAR:
        temp=5;
        Serial.println("NEAR");
        break;
      case DIR_FAR:
        temp=6;
        Serial.println("FAR");
        break;
      default:temp=7;
        Serial.println("NONE");
    }
  }
}

5、程序效果 如圖所示，當手滑動時，點陣顯示相應的滑動方向

02S10202.png

產品相關推薦

Erweima.png

資料下載

產品購買地址