(SKU:RB-01C047)Easy Driver Stepper Motor Driver
來自ALSROBOT WiKi
目錄 |
產品概述
2013年哈爾濱奧松機器人科技有限公司正式成為美國第一大電子開源硬件巨頭公司Sparkfun中國區域代理商。此款EasyDriver Stepper Motor Driver為全新Sparkfun原裝進口步進電機驅動器,其易于使用,能夠與任何可以輸出0-5V(3V 請短路SJ2 )脈沖信號的設備配合使用。EasyDriver通過接入7-30V電壓來給電機供電,并且可以驅動幾乎任何一款步進電機。EasyDriver的板載穩壓芯片可以設置為3.3V或者5V,可以直接接入4線步進電機,通過微控制器精確的控制步進電機的動作。注意:驅動器通電時,請勿連接或斷開電機。這將導致永久性損壞A3967芯片。
規格參數
- 驅動芯片:A3967
- MS1 and MS2 腳用于控制電機的細分(2、4、8),默認為8細分
- 兼容任何電壓的4、6、8線步進電機
- 可調電流控制
- 電源輸入范圍7-30V,電壓越高,高速時扭矩越高
使用方法
連接示意圖
使用Easy Driver Stepper Motor Driver 來控制四線兩向步進電機接線圖
示例代碼
int dirpin = 2; int steppin = 3; void setup() { pinMode(dirpin, OUTPUT); pinMode(steppin, OUTPUT); } void loop() { int i; digitalWrite(dirpin, LOW); // Set the direction. delay(100); for (i = 0; i<4000; i++) // Iterate for 4000 microsteps. { digitalWrite(steppin, LOW); // This LOW to HIGH change is what creates the digitalWrite(steppin, HIGH); // "Rising Edge" so the easydriver knows to when to step. delayMicroseconds(500); // This delay time is close to top speed for this } // particular motor. Any faster the motor stalls. digitalWrite(dirpin, HIGH); // Change direction. delay(100); for (i = 0; i<4000; i++) // Iterate for 4000 microsteps { digitalWrite(steppin, LOW); // This LOW to HIGH change is what creates the digitalWrite(steppin, HIGH); // "Rising Edge" so the easydriver knows to when to step. delayMicroseconds(500); // This delay time is close to top speed for this } // particular motor. Any faster the motor stalls. }
程序效果
將此代碼下載到Arduino控制器中,通電之后步進電機先順時針旋轉然后再逆時針旋轉。
產品相關推薦
產品購買地址
Easy Driver Stepper Motor Driver
周邊產品推薦
相關問題解答
Easy Driver Stepper Motor Driver如何使用
Easy Driver Stepper Motor Driver使用例子程序
相關學習資料
Easy Driver Stepper Motor Driver中文翻譯資料
示意圖
步進電動機的數據表
easydriver網站
bildr教程
快速入門指南
奧松機器人技術論壇